Size : 10mg
Synonyms:
| Description | AZD1208 is a novel, orally bioavailable, highly selective PIM kinase inhibitor with single nanomolar potency against all three PIM kinases. |
| Targets & IC50 | Pim3:1.9 nM, Pim2:5 nM, Pim1:0.4 nM |
| In vitro | AZD1208 dose-dependently inhibits the growth of MOLM-16 and KG-1a xenograft tumors in vivo. |
| In vivo | AZD1208 induces cell cycle arrest and apoptosis in cultured MOLM-16 cells, accompanied by a dose-dependent decrease in the phosphorylation of BAD, 4EBP1, and p70S6K. Additionally, AZD1208 effectively inhibits colony growth of primary AML cells derived from bone marrow aspirates and downregulates phosphorylation of Pim targets. |
| Kinase Assay | The activity of purified human PIM-1, PIM-2 and PIM-3 enzymes on substrate FL-Ahx-Bad (FITC-(AHX)RSRHSSYPAGT-COOH) is determined using a mobility shift assay on a Caliper LC3000 reader. The PIM-1 assay is performed in a 12 mL reaction containing 50 mM HEPES (pH 7.5), 1 mM DTT, 0.01% Tween 20, 50 mg/mL BSA, 10 mM MgCl2, 1.5 mM FL-Ahx-Bad peptide, 100 mM ATP, 2.5 nM PIM-1 and various amount of inhibitor. The reaction is quenched after 90 minute incubation at 25?C with?5 mL of stop mix consisting of 100 mM HEPES, 121 mM EDTA, 0.8% Coating Reagent 3 and 0.01% Tween 20. The ATP and enzyme concentrations for the PIM-2 assay are 5 mM and 2.5 nM, respectively, while 50 mM of ATP and 0.33 nM of enzyme is used for PIM-3 assays. For high [ATP] screenings, 5 mM ATP is used with 0.67 nM enzyme for both PIM-1 and PIM-2 or 0.11 nM PIM-3. Fluorescence of phosphorylated and unphosphorylated substrate is detected and a ratiometric value is calculated to determine percent turnover. IC50 values are determined from dose-response data using IDBS ActivityBase software. |
| Cell Research | AZD1208 is dissolved in DMSO. MOLM-16 cells, purchased from DSMZ and cultured in RPMI containing 10% fetal bovine serum (FBS) and 1% L-glutamine, are plated at 20,000 cells per well in 96 well plates overnight. Cells are treated for 72 hours with compound or control vehicle (dimethyl sulfoxide) and cell viability is measured after the addition of Cell Titer-Blue for 4 hours at 37?C and reading of fluorescence on a Tecan Infinite? 200. The GI50 is determined by calculating growth at each dose relative to vehicle treated cells and cell viability at the time of treatment. |
| Molecular Weight | 379.48 |
| Formula | C21H21N3O2S |
| Cas No. | 1204144-28-4 |
| Smiles | NC1CCCN(C1)c1c(\C=C2/SC(=O)NC2=O)cccc1-c1ccccc1 |
| Relative Density. | 1.307 g/cm3 (Predicted) |
| Storage | Keep away from moisture,Store under nitrogen,Store at low temperature Powder: -20°C for 3 years | In solvent: -80°C for 1 year Shipping with blue ice/Shipping at ambient temperature. | |||||||||||||||||||||||||||||||||||
| Solubility Information | DMSO: 50 mg/mL (131.76 mM), Sonication is recommended.  | |||||||||||||||||||||||||||||||||||
| In Vivo Formulation | 10% DMSO+40% PEG300+5% Tween 80+45% Saline: 1 mg/mL (2.64 mM), Sonication is recommended. Please add the solvents sequentially, clarifying the solution as much as possible before adding the next one. Dissolve by heating and/or sonication if necessary. Working solution is recommended to be prepared and used immediately. The formulation provided above is for reference purposes only. In vivo formulations may vary and should be modified based on specific experimental conditions. | |||||||||||||||||||||||||||||||||||
Solution Preparation Table | ||||||||||||||||||||||||||||||||||||
DMSO
Note : The dilution table applies only to solid products. For liquid products, please calculate the stock solution based on the stated concentration and/or density. | ||||||||||||||||||||||||||||||||||||
For example, if the intended dosage is 10 mg/kg for animals weighing 20 g , with a dosing volume of 100 μL per animal, and a total of 10 animals are to be administered, using a formulation of 
10% DMSO+ 40% PEG300+ 5% Tween 80+ 45% Saline/PBS/ddH2O , the resulting working solution concentration would be 2 mg/mL.Dissolve 2 mg of the compound in 100 μL DMSO to obtain a stock solution at a concentration of 20 mg/mL . If the required concentration exceeds the compound's known solubility, please contact us for technical support before proceeding.
1) Add 100 μL of the DMSO stock solution to 400 µL PEG300 and mix thoroughly until the solution becomes clear.
2) Add 50 µL Tween 80 and mix well until fully clarified.
3) Add 450 µL Saline,PBS or ddH2O and mix thoroughly until a homogeneous solution is obtained.
| Size | Quantity | Unit Price | Amount | Operation |
|---|
